This structure defines various settings for the ValueCAN 4-4 and 4-2EL device.
Remarks
| Item | Description |
|---|---|
perf_en
Performance test. Default value = 0
can1
See CAN_SETTINGS structure
canFD1
See CANFD_SETTINGS structure
can2
See CAN_SETTINGS structure
canFD2
See CANFD_SETTINGS structure
can3
See CAN_SETTINGS structure
canFD3
See CANFD_SETTINGS structure
can4
See CAN_SETTINGS structure
canFD4
See CANFD_SETTINGS structure
network_enables
Bitfield containing the software license enables. Depending on the hardware license purchased the customer may have to conditionally select which hardware channels to enable. For example the neoVI Red license allows the user to enable any 2 Dual Wire CAN channels and any 2 LIN channels. To enable a specific network its corresponding bit must be set (1). In order to transmit or receive on a network it must be enabled.
network_enables_2
Bitfield containing the software license enables. Depending on the hardware license purchased the customer may have to conditionally select which hardware channels to enable. For example the neoVI Red license allows the user to enable any 2 Dual Wire CAN channels and any 2 LIN channels. To enable a specific network its corresponding bit must be set (1). In order to transmit or receive on a network it must be enabled.
lin1
See LIN_SETTINGS structure
network_enabled_on_boot
Normally neoVI only initiates its comm channels when CoreMini is running or if neoVI is online with DLL/Vehicle Spy 3. Practically this means the the CAN controllers stay in Listen Only mode until the device goes online. Once online the neoVI loads the user settings. Setting this parameter to 1 will change this behavior so that the neoVI enables its controllers immediately on boot.
Default value = 0
iso_9141_kwp_enable_reserved
Reserved
iso9141_kwp_settings
See ISO9141_KEYWORD2000_SETTINGS structure
iso_parity
ISO9141 Parity setting: 0 - no parity, 1 - even, 2 - odd
iso_msg_termination_1
ISO9141 message termination setting: 0 - use inner frame time 1 - GME CIM-SCL
network_enables_3
Bitfield containing the software license enables. Depending on the hardware license purchased the customer may have to conditionally select which hardware channels to enable. For example the neoVI Red license allows the user to enable any 2 Dual Wire CAN channels and any 2 LIN channels. To enable a specific network its corresponding bit must be set (1). In order to transmit or receive on a network it must be enabled.
text_api
See STextAPISettings structure
ethernet
See ETHERNET_SETTINGS structure
Flags
Not used
pwr_man_enable
1 = enable Power Management, 0 = disable.
Default value = 0
pwr_man_timeout
Number of milliseconds of no bus activity required before neoVI enters low power mode. Note pwr_man_enable must be set for power management to be enabled.
Default value = 10000
HSCAN : 0
MSCAN : 1
LIN1 : 2
LIN2 : 3
VIRTUAL : 4
HSCAN2 : 5
LSFTCAN1 : 6
SWCAN1 : 7
HSCAN3 : 8
GMCGI : 9
J1850 : 10
LIN3 : 11
LIN4 : 12
J1708 : 13
HSCAN4 : 14
HSCAN5 : 15
KLINE1 : 0
KLINE2 : 1
KLINE3 : 2
KLINE4 : 3
FLEXRAY1A : 4
UART : 5
UART2 : 6
LIN5 : 7
MOST25 : 8
MOST50 : 9
FLEXRAY1B : 10
SWCAN2 : 11
ETHERNET_DAQ : 12
ETHERNET : 13
FLEXRAY2A : 14
FLEXRAY2B : 15
HSCAN6 : 0
HSCAN7 : 1
LIN6 : 2
LSFTCAN2 : 3
OP_ETH1 : 4
OP_ETH2 : 5
OP_ETH3 : 6
OP_ETH4 : 7
OP_ETH5 : 8
OP_ETH6 : 9
OP_ETH7 : 10
OP_ETH8 : 11
OP_ETH9 : 12
OP_ETH10 : 13
OP_ETH11 : 14
OP_ETH12 : 15