The sections below list all of the valid device parameters for each supported neoVI device.
neoVI Fire Parameters
The valid parameters for a neoVI Fire device are listed below. See SFireSettingsStructure for a listing of the valid values for each parameter.
can1 can2 can3 can4 (see CAN Network Parameters)
swcan (see Single Wire CAN Network Parameters)
lsftcan (see CAN Network Parameters)
lin1 lin2 lin3 lin4 (see LIN Network Parameters)
cgi_baud
cgi_tx_ifs_bit_times
cgi_rx_ifs_bit_times
cgi_chksum_enable
network_enables
network_enabled_on_boot
pwm_man_timeout
pwr_man_enable
misc_io_initial_ddr
misc_io_initial_latch
misc_io_analog_enable
misc_io_report_period
misc_io_on_report_events
ain_sample_periodain_threshold
iso15765_separation_time_offsetiso9141_kwp_settings (see ISO9141_KWP Network Parameters)
perf_en
iso_parity
iso_msg_termination
network_enables_2
valueCAN3 Parameters
can1 can2 (see CAN Network Parameters)
network_enables
network_enabled_on_boot
iso15765_separation_time_offset
perf_en
misc_io_initial_ddr
misc_io_initial_latch
misc_io_report_period
misc_io_on_report_events
The valid parameters for CAN network settings on a neoVI device are listed below. Substitue the number of the CAN channel on the device for the 'x' . The current valid CAN network specifiers are can1 through can4, depending the capabilities of the device. See CAN_SETTINGSStructure for a listing of valid values for each parameter.
canx/Mode
canx/SetBaudrate
canx/Baudrate
canx/NetworkType
canx/TqSeg1
canx/TqSeg2
canx/TqProp
canx/TqSync
canx/BRP
canx/auto_baud
The valid parameters for single wire CAN network settings on a neoVI device are listed below. See SWCAN_SETTINGSStructure for a listing of valid values for each parameter.
swcan/Mode
swcan/SetBaudrate
swcan/Baudrate
swcan/NetworkType
swcan/TqSeg1
swcan/TqSeg2
swcan/TqProp
swcan/TqSync
swcan/BRP
swcan/high_speed_auto_switch
swcan/auto_baud
The valid parameters for a LIN network on a neoVI device are listed below. Substitute the number of the LIN channel on the device for the ‘x’. The current valid LIN network specifiers are lin1 through lin4. See LIN_SETTINGSStructure for a listing of valid values for each parameter.
linx/Baudratelinx/spbrg
linx/brgh
linx/MasterResistor
linx/Mode
The valid parameters for the ISO9141_KWP Network are listed below. For the iso9141_kwp_settings/init_steps/x/ parameters, substitute the number of the desired step for the ‘x’. The current valid init_steps range is 0 through 15, for a total of 16 steps.
iso9141_kwp_settings/Baudrate
iso9141_kwp_settings/spbrg
iso9141_kwp_settings/brgh
iso9141_kwp_settings/init_steps/x/time_500us
iso9141_kwp_settings/init_steps/x/k
iso9141_kwp_settings/init_steps/x/l
iso9141_kwp_settings/init_step_count
iso9141_kwp_settings/p2_500us
iso9141_kwp_settings/p3_500us
iso9141_kwp_settings/p4_500us
iso9141_kwp_settings/chksum_enabled