neoECU 10: IO Map

The neoECU 10 uses Misc IO to configure the device. Table 1 shows the Misc IO table for neoECU 10. Examples of using the Misc IO can be found at this Link: Examples. The examples show how to use different features like PWM I/O, Analog inputs, LED, SW CAN, and other configurations.

Table 1: neoECU 10 Misc Pin

Misc IO Number	Name Of IO Controlled	Function of IO	Notes
7	SW CAN M1	Works with MISC IO 8 to set SW CAN State	Set is output to 1: For value use; Normal Misc 7=1 and Misc 8=1; HVWU Misc 7=1 and Misc 8=0
8	SW CAN M0	Works with MISC IO 7 to set SW CAN State	Set is output to 1: For value use; Normal Misc 7=1 and Misc 8=1; HVWU Misc 7=1 and Misc 8=0
9	LSFT Enable	Enables LSFT CAN	Set is output to 1: For value use; 1 for Enable, 0 to disable
10	LSFT _STB#	Enables LSFT CAN	Set is output to 1: For value use; 1 for Enable, 0 to disable
15	LSFT/SW_EN#	Enables LSFT and SW CAN	Set is output to 1: For value use; 1 for Enable, 0 to disable
16	LSFT/SW#_SEL	Enables LSFT CAN	Set is output to 1: For value use; 1 for LSFT, 0 for SW
32	MISC IO2	Controls MISC IO2	Set is output to 1: Value Sets Value
33	MISC IO1	Controls MISC IO1	Set is output to 1: Value Sets Value
45	MISC IO3	Controls MISC IO3	Set is output to 1: Value Sets Value
46	MISC IO4	Controls MISC IO4	Set is output to 1: Value Sets Value
47	MISC IO5	Controls MISC IO5	Set is output to 1: Value Sets Value
48	MISC IO6	Controls MISC IO6	Set is output to 1: Value Sets Value
50	PWM2: IO6 On Device	Is IO6 PWM	Set is output to 0: Value Sets 1=PWM, 0=MISCIO
51	PWM3: IO5 On Device	Is IO5 PWM	Set is output to 0: Value Sets 1=PWM, 0=MISCIO
52	PWM4: IO4 On Device	Is IO4 PWM	Set is output to 0: Value Sets 1=PWM, 0=MISCIO
55	PWM5: IO2 On Device	Is IO2 PWM	Set is output to 0: Value Sets 1=PWM, 0=MISCIO
57	PWM7: IO3 On Device	Is IO3 PWM	Set is output to 0: Value Sets 1=PWM, 0=MISCIO
58	PWM8: IO1 On Device	Is IO1 PWM	Set is output to 0: Value Sets 1=PWM, 0=MISCIO
65	LED 3	Controls the state of LED 3	Set is output to 1: Value Controls state
66	LED 2	Controls the state of LED 2	Set is output to 1: Value Controls state
67	LED 1	Controls the state of LED 1	Set is output to 1: Value Controls state

The states and values for the MiscIO can be controlled though Function Blocks. The most common command to use to configure the Misc IO is Set Value. Figure 1 shows the Expression editor. To get to the Misc IO, select Physical IO on the left (Figure1: ) and then Misc IO to the right (Figure1: ). At the bottom there are three properties (Figure1: ). The "Value" option is used to set or read a value from that IO. For example setting the value of an output, or reading the state of an input. The "Is Output" property is to set the direction of the IO. One reason for doing this would be setting the direction for the IO. For example if you are working with a Digital Output, you would set the "Is Output" property to 1 (output). If this IO is not an output, but an input, set this property to be 0 (input).

Figure 1: Expression editor configuring Misc Pins

One example of working with the Misc IO would be using the LED's. From Table 1, LED 3 is Misc IO 65. To work the LED, it would first need to be set to an output. In a Set Value command the "Is Output" Property would be set to "1". This sets the direction of the IO. An LED is an output, so this IO was set to be an output. Next the "Value" property can be used to set the state of the LED. In the example below, the Value was set to 1 to turn the LED on.

Figure 2: Turning LED On