TCP/IP

Vehicle Spy's TCP/IP view shows the current status of its TCP/IP connections for a selected ethernet network and allows editing of some parameters. A valid TCP/IP connection is required for Diagnostics over IP (DoIP). A maximum of 128 connections are allowed. TCP/IP view is opened from the Spy Networks menu.

Ethernet communication involves many protocols and TCP/IP view supports the following:

Table 1: Ethernet Protocols Supported in VSpy's TCP/IP

Acronym	Name	Description
TCP	Transmission Control Protocol	Controls data flow between two nodes.
IP	Internet Protocol	Controls addressing to ensure data gets to the correct node.
UDP	User Datagram Protocol	Supports data flow from one node to all nodes.
IGMP	Internet Group Management Protocol	Supports data flow from one node to nodes in a specific group.
AutoIP	Automatic Private IP Addressing	Link-local IP address configuration per RFC 3927.
DHCP	Dynamic Host Configuration Protocol	Dynamic IP address distribution per RFC 2132.
ARP	Address Resolution Protocol	Maps virtual IP addresses to physical MAC addresses.

TCP in Vehicle Spy

TCP has a virtual network in Vehicle Spy to expose data hidden within the raw ethernet traffic found on the physical networks like "Ethernet" and "OP (BR) ETH01". TCP also has a predefined column set on Messages view to quickly organize the data from the virtual networks.

TCP requires the Tools > Options > Spy Networks tab setting "Use PC Ethernet interface" = ON.

MAC Address

The MAC Address (Media Access Control) (Figure 1:) is a static address associated with a physical ethernet device. Vehicle Spy displays the address as a series of six bytes in hexadecimal format. The first three bytes of the MAC Address are 00:FC:70 for ICS hardware.

• Inherit from device - use the MAC address of ICS hardware that is online with VSpy.

• Manually assigned - use the MAC address entered.

IP Address

The IP Address (Internet Protocol) (Figure 1:) is a dynamic address associated with a virtual node which is assigned as needed to route ethernet traffic correctly. Vehicle Spy displays the address as a series of four bytes in decimal format. A typical address to use is in the range from 192.168.000.000 to 192.168.255.255 which is reserved for private networks.

• Inherit from OS - use the IP address of the operating system VSpy is currently running in.

• Manually assigned - use the IP address entered.

• AutoIP + DHCP - use an IP address that configures itself after VSpy goes online with hardware.

The Subnet mask (Figure 1:) defines a network ID and host ID within the IP Address. The mask is logically AND'ed with the IP address to determine the IDs. Binary ones in the mask indicate the network ID and binary zeroes indicate the host ID. Vehicle Spy displays the mask as a series of four bytes in decimal format. A typical mask to use is 255.255.255.000.

The Gateway Address (Figure 1:) is the address of a router connected to other networks. This is where data will go if it has an unknown destination. Vehicle Spy displays the address as a series of four bytes in decimal format.

Figure 1: Use TCP/IP view to setup a MAC and IP address for Vehicle Spy and see the status of its TCP/IP connections.

Additional Settings

Additional settings are located on the right side of TCP/IP view. (Figure 1:)

Ethernet network determines which network the entire TCP/IP view is focused on.

If Report IGMP group memberships is enabled then Vehicle Spy will broadcast its group memberships after going online with hardware. IGMP supports data flow from one node to nodes in a specific group.

If Send gratuitous ARP announce is enabled then Vehicle Spy will announce its MAC and IP addresses after going online with hardware.

TCP/IP Status Table

All of Vehicle Spy's TCP/IP connections for the selected network are indicated in the status table located in the lower area of TCP/IP view (Figure 1:).

Table 2: TCP/IP Status Table

TCP/IP Column	Description
Remote IP	IP address that Vehicle Spy is trying to connect to.
Remote port	Port number that Vehicle Spy is trying to connect to.
Local port	Port number being used by Vehicle Spy.
State	Current state of the TCP/IP connection. Closed Established Listen UDP - broadcast message sent to multiple nodes
Rx seq #	Last sequence number received by Vehicle Spy.
Rx window	Width (in bytes) of the sliding receive window.
Rx count	The number of segments received by Vehicle Spy.
Tx seq #	Last sequence number transmitted by Vehicle Spy.
Tx window	Width (in bytes) of the sliding transmit window.
Tx count	The number of segments transmitted by Vehicle Spy.
Re-Tx count	The number of segments retransmitted by Vehicle Spy.
Error count	The number of errors detected for the TCP/IP connection.
Comments	More details about the state of the TCP/IP connection